NordCap Contact cooling plate KP-GN 2/1 for 2 x GN 1/1, plug-in, 4 to 12 °C, R-290

Product details

The NordCap contact cooling plate KP-GN 2/1 is a plug-in installation unit for GN 1/1 with machine compartment below, which cools products at 4 to 12 °C for a short time.

The KP-GN 2/1 is designed as an installation unit for 2 x GN 1/1. With external dimensions of 645 x 525 x 339 mm (W x D x H) and a recess of 660 x 540 mm (W x D) results in a footprint of 0.35 m2. The temperature range is 4 to 12 °C, relative to 25 °C ambient temperature and 60 % relative humidity, the device is assigned to climate class 3. Important for planning: The contact cooling plate is only suitable for short-term cooling of the products, a long-term or permanent cooling is not possible.

The temperature is controlled by electronic control. The machine compartment is located at the bottom of the device, the contact cooling plate is connected ready for plugging to 230 V. The plate has four mounting flaps for mounting in the recess.

The exterior and interior cladding are made of stainless steel CNS 1.4301, the viewing sides are each ground. The insulation is provided by PUR hard foam with a thickness of up to 50 mm. The light outer bulging beach of the plate is used to capture the condensation water. As a special accessory, a capacitor protection is optionally available.

The natural refrigerant R-290 (propane) is cooled at a filling quantity of 55 g, the greenhouse potential is indicated with GWP100 (AR5) 3. The cooling capacity is 190 W at -10 °C evaporation temperature, the connection value is 0.14 kW at 230 V and 50 Hz. The energy consumption is indicated with 2.45 kWh in 24 hours. The net weight is 38 kg, the contact cooling plate is produced in Austria.

• 1 x KP-GN 2/1 contact cooling plate

• Manufacturer item number: 484255471
• Mounting method: Mounting device, 4 x mounting bracket
• Suitable: for GN 1/1
• External dimensions (W x D x H): 645 x 525 x 339 mm
• Mounted cutout (W x D): 660 x 540 mm
• Surface area: 0,35 m2
• Temperature range: 4 to 12 °C (at 25 °C ambient temperature and 60 % relative humidity)
• Climate class: 3 (+25 °C ambient temperature, 60% relative humidity)
• Control: electronic
• Connection type: plug-ready, machine compartment below
• Refrigerant: R-290 (propane), filling quantity 55 g, GWP100 (AR5) 3
• Cooling capacity: 190 W at -10 °C Evaporation temperature
• Connection: ready to plug, 0.14 kW, 230 V, 1-phase, 50 Hz
• Energy consumption: 2.45 kWh/24 h
• Insulation: PUR hard foam, up to 50 mm
• exterior facing: CNS 1.4301, face-ground
• Internal facing: CNS 1.4301, face-ground
• Weight: 38 kg net
• Country of origin: Austria

• Plug ready, machine compartment below
• Electronic control
• Mounting device with 4 mounting flaps
• Outer Wulf Beach for the collection of condensation
• Natural refrigerant R-290
• stainless steel CNS 1.4301 outside and inside, face ground
• PUR hard foam insulation up to 50 mm

Notes on establishment and operation

Only suitable for short-term cooling of the products, a long-term or permanent cooling is not possible. The installation cut-out is 660 x 540 mm (W x D).

Operating instructions

Download user manual (PDF)

Energy labelling

No EU energy label is stored for this device on the manufacturer's side.

Product safety (GPSR)

Manufacturer: AKE Ausseer Kühle- und Edelstahltechnik GmbH, Pichl 66, 8984 Bad Mitterndorf, Austria
Responsible person in the EU: NordCap GmbH & Co. KG, Thalenhorststraße 15, 28307 Bremen, Germany, telephone: +49 421 48557-0, e-mail: produktsicherheit@nordcap.de

Safety instructions: Read and follow the instructions provided with all safety and warning instructions before installation, connection and use.